SMART EVO 1
-
SHOP
- Automation control panel
- Water treatment control panels
- Control panels for food-processing
- electrical components and spare parts
- PLC programming
- Groups of pressurization
- Fire-prevention groups
- Surface pumps
- Submersible pumps for wells and tanks
- Treatment of drinking water
- treatment of waste water
Technical features
- Single phase power supply 100-240Vac ±10% 50/60Hz (SMART EVO Mono);
- Three phase power supply 100-240Vac ±10% 50/60Hz (SMART EVO -Tri);
- Three phase power supply 310-450Vac ±10% 50/60Hz (SMART EVO -Tri);
- G/P1 and G/P2 normally open inputs for start-up command;
- 3 inputs for single-pole level sensors (COM-MIN-MAX);
- T1 and T2 input...
Technical features
- Single phase power supply 100-240Vac ±10% 50/60Hz (SMART EVO Mono);
- Three phase power supply 100-240Vac ±10% 50/60Hz (SMART EVO -Tri);
- Three phase power supply 310-450Vac ±10% 50/60Hz (SMART EVO -Tri);
- G/P1 and G/P2 normally open inputs for start-up command;
- 3 inputs for single-pole level sensors (COM-MIN-MAX);
- T1 and T2 inputs for motor clicson;
- Normally open input for alarm activation;
- AUTOMATIC-0-MANUAL buttons (spring return);
- DIP-SWITCH selectors for:
- level alarm enable from sensors,
- thermal cut-out activation delay 5/10 seconds,
- alarm output settings,
- alarm reset enable from motor clicson,
- Filling/Emptying mode,
- start/stop float enable,
- enable of delay on board activation on power mains return,
- motor switching module enable (on SMART EVO 2);
- Green led: power ON / failure or incorrect phase sequence;
- Green leds: automatic mode enabled;
- Green led: motor active;
- Red led: level alarm from sensors or GA input;
- Red leds: motor overload alarm/minimum current alarm;
- Red leds: motor clicson activation alarm;
- Electronic control of maximum current due to overload, with assisted calibration;
- Electronic control of minimum current due to dry run, with assisted calibration;
- Automatic reset due to minimum current alarm;
- Protections of auxiliary circuits and motor with fuses;
- Cumulative alarm output with voltage-free contacts (COM-NO-NC resistive load - 5A / 250V);
- Cumulative alarm output, live (12Vcc / 100mA);
- Door lock general disconnect switch;
- Provision for start-up capacitors, single phase version (not included);
- Box in ABS, IP55;
- Ambient temperature: -5/+40 °C;
- Relative humidity 50% at 40 °C (condensate free).
SMART EVO 1 There are 5 products.
-
DON’T FIND WHAT YOU’RE LOOKING FOR?
Contact us! What you see is a small part of that we can supply. click on "Richiedi informazioni su questo prodotto" or use the livechat. You can contact us also by e-mail or by phone.
-
SMART EVO 1- MONO
POWER SUPPLY: single phase 230V POWER: da 0,37kw a 2,2 kw (da 0,5 a 3 Hp) CURRENT: 18A DIMENSION: H 320mm, L 240mm, W190mm WEIGHT: 2,5 Kg
-
SMART EVO 1- TRI/7.5
POWER SUPPLY: three-phase 400V POWER: da 0,55 kw a 7,5 kw (da 0,75 a 10 Hp) CURRENT: 16A DIMENSION: H 320mm, L 240mm, W190mm WEIGHT: 5.5 Kg
-
SMART EVO 1 -TRI/11
POWER SUPPLY: three-phase 400V POWER: from 0.55 kw to 11 kw (da 0.75 a 15 Hp) CURRENT: 25 A DIMENSION: H 320mm, L 240mm, W190mm WEIGHT: 6 Kg
-
SMART EVO 1- TRI/15
POWER SUPPLY: three-phase 400V POWER: from 7.5 kw to 15 kw (from 0.75 to 20 Hp) CORRENTE: 32 A DIMENSION: H 320mm, L 240mm, W190mm WEIGHT: 6.5 Kg
